- Описание
- Отзывы (0)
TSS LIMITER-LOGGER PRO V.2.0
Limiter for ship models with online telemetry and logger
Price: €95
add to cart
DESCRIPTION
The energy limiter for radio-controlled models (hereinafter the limiter) is intended for calculation and limitation of the energy consumed by the model.
The device is equipped with the Bluetooth Low Energy (BLE) interface for communication with mobile devices or computers which allows to perform its settings and receive the current readings without need of having direct access to and its removing from the model.
The device can be used both for running the competitions to limit the energy consumed by the model from the accumulator and for training intentions to set the model and take the actual readings on current, voltage, energy and consumable battery capacity.
The device fully meets the Naviga requirements which allows using it in all kinds of registered or non-registered competitions according to Naviga rules. In event of rule changes, the new array of device settings will be available in new firmware upgrades of the device. The firmware upgrade is performed through the user`s phone, you need not send the device anywhere.
TECHNICAL SPECIFICATION
|
Parameter |
Value |
Note |
|
Measured voltage |
0 – 44V |
DC |
|
Voltage measurement accuracy |
±0.1% |
|
|
Measured current (up to 20 sec) |
1 – 150A |
|
|
Measured current (DC) |
1 – 100A |
|
|
Current measurement accuracy |
±0.5% + ±50mA |
|
|
Measured energy |
0 – 300,000Wh |
|
|
Energy measurement accuracy |
±1.0% |
|
|
Temperature measurement |
-10 – +150⁰C |
Device temperature |
|
Temperature measurement accuracy |
±1.0⁰C |
|
|
Sampling frequency |
300Hz |
|
|
Series resistance |
0.25mOhm |
|
|
Current consumption |
6mA |
|
|
BEC voltage |
4 – 13V |
|
|
Type of communication interface |
BLE |
Bluetooth Low Energy 5.0 |
|
Communication Interface range |
100m |
In direct visibility |
|
Receiver signal |
0.7 – 2.3ms |
Standard PPM 3.3-10V |
|
Working temperature range |
0 – 50⁰C |
|
|
IP rating |
IP67 |
|
|
Dimensions of the device |
22.5 х 19.5 х 10.5mm |
No wires included |
|
Weight |
18g |
Including all wires and plugs |
|
Wire to receiver length |
240mm |
|
|
Wire to ESC length |
40mm |
|
|
Type of signal wires |
26AWG (JR) |
|
|
Length of the power wire |
100mm |
|
SHORT DESCRIPTION
In total, the device has 14 sets of settings, 8 (6 - 14) of which are user-defined and are subject to change.
The device has 6 sets of preset settings. These settings cannot be changed and 1 – 5 sets fully comply with the Naviga rules.
LOGGER AND TELEMETRY
The device is equipped with logger, which can be used as an online telemetry and as an ordinary logger, allowing you to read the meashured data after the race.
Logger and telemetry display the following parameters:
- Current;
- Average current for 10 seconds;
- Voltage;
- Measured energy;
- Measured capacity;
- Temperature (own);
- Power consumption for the race (economizer);
- Average current for the race;
- Average voltage for the race;
- Measured race time.
A display of the average current per race and the average voltage per race will be added soon.
CONFIGURATION AND SOFTWARE
The basic settings of the limiter can be changed using a button that is connected via a wire that goes to the receiver.
Functions of setting by button is given in the table:
|
Settings set number |
Purpose |
Energy limitation |
|
0 |
Training mode, telemetry only |
∞ |
|
1 |
Mini Eco, Mono, Hydro |
21Wh |
|
2 |
Eco Expert, Mono I, Hydro I |
60Wh |
|
3 |
Mono II, Hydro II |
120Wh |
|
4 |
FSR-E |
180Wh |
|
5 |
For tests only |
2Wh |
|
Function |
Parameter |
Note |
|
Reset of energy calculation |
Hold down for 10 ± 3 seconds |
Indication can be updated with delay in one period |
|
Switching the set of settings up |
Push once |
Only if the energy calculation is not started. Cyclically switching between 0–5 sets |
|
Switching the set of settings down |
Hold down for 1 second |
Only if the energy calculation is not started. Cyclically switching between 0–5 sets |
|
Password reset |
Hold down for 30 ± 10 seconds |
Only if the energy calculation is not started. |
|
Manual start of bootloader |
Hold down before switching on, release as soon as the green LED goes out |
In normal device operation it is not used. Required if there are problems with updating the firmware in a regular manner. |
USER MANUAL
TSS Limiter v.1.0 Quick start guide.pdf
TSS Limiter v.1.0 User manual.pdf
Отзывы
